The oil injector of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is a device used for supplying lubricating oil to internal steam turbines using an oil injector system. Its power oil comes from an independent oil pump (starting from an AC high-pressure oil pump), and the main oil pump is a centrifugal pump. To avoid accidents caused by self suction and air leakage, positive pressure oil injection is required. Therefore, the oil supply system is a dual oil injector system with an oil injector for lubrication and an oil injector for the main oil pump. But there are also single jet oil systems that combine the above two functions, which are used in smaller units. In recent years, large units have also used single jet oil systems, such as N300-16.7-537/537 units:

The occurrence of low lubricating oil pressure or low oil injection pressure in the steam turbine unit is a common phenomenon and an unsafe working condition that needs improvement. Lianyungang Lingdong Electromechanical Equipment Co., Ltd. has the ability to do this work and has solved the problem of oil injectors, which is a successful example of cooperation with a lubrication box manufacturer.

For example, the lubricating oil pressure of a 50MN unit in a large petrochemical enterprise in Northeast China is only 0.06MPA, and the on-site requirement is 0.1 MPA or slightly higher. According to the original size of the oil injector, the oil supply capacity is 1050l/min. Taking into account factors such as level difference, resistance of the oil cooler, and the relationship between flow rate and resistance, the required oil volume (should be 1420l/min) was calculated. The improved oil injector designed based on this has successfully met the requirements. Lubricating oil pressure is 0.11MPA. The safety of unit operation is also guaranteed.

A certain 300MW unit is a different type of problem, as there is a "dangerous" speed zone during the start-up and acceleration process. At this point, the outlet oil pressure of the oil injector drops to a low of 0.135 MPA, and it should be greater than 0.2 MPA to be safe. The reason is that at this speed, the main oil pump has a considerable amount of oil pressure, which impacts the check valve of the main oil pump and reduces the outlet check valve of the high-pressure AC oil pump. The two affect each other, reducing the amount of oil input and lowering the oil pressure. The method of encountering such problems in the manufacturing plant is to install an oil injector to start the pressure reducing slide valve, in order to avoid the "dangerous" speed. Under this working condition, the main oil pump also discharges oil according to the speed, without impacting the AC oil pump supply oil, until it reaches the safe speed (which is 500-600 rpm higher than the dangerous speed). The function of starting the pressure reducing slide valve is automatically released, and the oil injector also has a supplementary function until it is fully linked with the main oil pump to supply lubricating oil.

In addition, Lianyungang Lingdong Electromechanical Equipment Co., Ltd. also supplies generator air side sealing oil injectors.

你可能喜歡看：

installation and working engineering of coal powder sampler

11-25 1018

The installation and operation of The coal powder sampler and mobile coal powder sampler of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. drill holes on The flue, extend The sampling tube into The flue, and make The sampling head face The direction of The incoming smoke flow.

The purpose of fly ash sampler

11-25 933

The purpose and function of The fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is that The carbon content of boiler fly ash is an important indicator reflecting The combustion rate of coal-fired boilers in Thermal power plants.

squirting air extractor

08-20 929

Assembly and installation of oil injectors

11-25 921

The oil supply and lubrication oil injectors are completely identical in structure, mainly composed of orifice nozzles, diffusion tubes, sleeves, filters, etc.

The function of an oil injector is to use a small amount of lubricating oil as power

08-20 866

The function of The oil injector of Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is to use a small amount of lubricating oil as power, suck in a large amount of oil, and supply lubricating system and main oil pump with oil at a certain pressure.

The principle of steam jet pump and steam injector

11-25 854

A steam injector is a device that is powered by steam and is needed in modern engineering. It does not require electricity, has no moving or rotating parts, is simple in system, and works reliably, so it is used.

The basic principle of lubricating oil system injectors

11-25 810

The oil injector is composed of a nozzle, a filter screen, an expansion pipe, and an inlet pipe. in addition to supplying The inlet oil of The centrifugal main oil pump, it also supplies lubricating oil system and sealing oil system oil.

Vapor-liquid two-phase flow is used in continuous sewage expansion vessel

08-20 783

Lianyungang Lingdong Electromechanical Equipment Co., Ltd. is a manufacturer of gas-liquid two-phase flow and electric auxiliary equipment such as continuous discharge expansion vessels.

Portable constant velocity fly ash sampler for regular coal powder sampling on The air and coal powder pipeline

08-20 779

The portable constant velocity fly ash sampler produced by Lianyungang Lingdong Electromechanical Equipment Co., Ltd., also known as The fly ash constant velocity sampler or The swirling fly ash constant velocity sampler,

Working status of oil injector and main oil pump

11-25 769

The working status of The oil injector and main oil pump, The analysis of The reasons for The drop in The inlet oil pressure test of The main oil pump of a 200MW steam turbine, and The composition of The oil supply system of The 200MW steam turbine generally adopt a centrifugal main oil pump oil supply system with dual injectors.

• Previous：The purpose of fly ash sampler
• Next：A coal powder sampler can also be referred to as a portable coal powder sampler